All sizes are available with an optional clear viewing lid. The clear polycarbonate lid version makes an ideal outdoor meter housing.
 All meters, LED readouts, and adjusting knobs can be mounted right under the lid with the optional aluminum display panel faceplate mounted on stud bolt posts. 

Optional internal hinges/lid screws can replace the standard lid screws and quickly turn these enclosures into wall-mounted indoor/outdoor cabinets with doors.

Rose+Bopla’s Fiberglass Modular Flange System consists of three different enclosures that can be used as stand alone units or can be quickly bolted together with connecting tunnel flanges and wedges. This fast system of joining enclosures together
not only guarantees a watertight seal, but also offers greatly expanded internal component mounting space. The length and width dimensions are expandable by adding additional enclosures.
     These 3 expandable systems offer all the advantages of molded products: clean design, tight tolerances, consistent dimensions, strength, low cost and resistance to weather and industrial corrosion. They also offer what is not normally available with molded products: expansion capability. 
     All units are made from compression-molded fiberglass mats that are UV stabilized. This system offers strength, ruggedness and weather/corrosion resistance, unmatched by metal enclosures. The rugged compression molded plastic will not give off toxic halogenated gases when burned. This makes these units ideal for areas where strict fire codes limit the use of plastic cases in harsh manufacturing high fire hazard areas. These fiberglass modular enclosures are ideal for electrical junction boxes in caustic petro-chemical plants or electroplating plants. 
     Rose+Bopla’s fiberglass modular enclosures have also been used to house car wash controls and as outdoor post-mounted railroad signal control boxes. These units can be used alone as individual control or junction boxes, or can be snapped together quickly to create an expandable, wall-mounted, outdoor, electrical control center. These modular enclosures are ideal for outdoor use, as they are impervious to sun, rain, sleet, ice and acid rain. These boxes will outlast any metal unit outdoors. 
     Each enclosure includes compression molded lid and base, non-reinforced fiberglass (POCAN) 3/4 turn lid screws and a non-removable polyurethane gasket. Flanges, connecting tunnels, hinges, mounting plates etc., are options and must be ordered separately. (Flange wedges are included with flanges). 
     Optional pre-threaded flanges have molded-in knockouts, which are easily removed with a screwdriver. This exposes the molded-in threads designed for Rose+Bopla’s fiberglass watertight cable grips. The grips are threaded and offer a watertight power cable entry/exit in seconds. The optional blank flange can be machined to fit any connector requirements, or un-machined, can be used to fill flange openings.
     Wall mounting holes are molded into each box. The lid must be removed to wall mount with this method. Optional external wall mounting brackets can be bolted onto the rear of the box. The lid does not have to be removed when using external wall-mount brackets.

1401: The 1401 model is the smallest of the units. This unit has two removable side flanges that allow rapid installation of electrical power cables with various Rose+Bopla flanges available.
270mm/10.63" L x 170mm/6.69" W x 135mm/5.31" H, Opaque Lid
270mm/10.63" L x 170mm/6.69" W x 150mm/5.91" H, Clear Lid.

1402: This is the intermediate size of the Rose+Bopla Fiberglass Modular Flange Units. Two 1402 units make one 1403 unit. This unit is square and has four removable flanges, which allow for the rapid installation of electrical power cables with various Rose+Bopla flanges available.
270mm/10.63" L x 270mm/10.63" W x 135mm/5.31" H, Opaque Lid
270mm/10.63" L x 270mm/10.63" W x 150mm/5.91" H, Clear Lid

1403: The largest of the Rose+Bopla Fiberglass Modular Flange Units with six removable flanges, the 1403 offers unrestricted access on all sides when installing electrical power cables. This model is exactly twice the size of the 1402 model. It can be used as a standalone unit or connected to other units for expanded internal mounting space.
540mm/21.26" L x 270mm/10.63" W x 135mm/5.31" H, Opaque Lid
540mm/21.26" L x 270mm/10.63" W x 150mm/5.91" H, Clear Lid

Note: Dimensions are external. Metric is the primary dimension. Inch conversions and weights are for the user's convenience and
are for reference only.

Note: Flanges must be ordered separately

We have attempted to present the information about our vendor's products on this website in a straight-forward manner. We offer this information as accurate at the time of publication. Specifications are subject to change without notice. Electro-Stock, Inc. is not responsible for inadvertent errors.

About Us • FAQ • Services • Terms & Conditions • Policies

Since 1983